If you ’re looking for an loose DIY project try out this DIY wooden plantation owner box . My favorite thing to establish in them are succulent but you could utilise them for just about anything !

Audrey ’s Little Farm may earn a perpetration after chatter connection on this pageboy at no additional price to you . Learn more .

I have grown up in a family of very handy hands and I ’d like to say that at least a few of their woodwind working skills have been passed down to me .

The Process of Making a Wood Planter Box

My gramps was a contractile organ as well as two of my uncle , and my dada Theodore Dwight Weld , make fence , and has built quite a few barns .

So between all of these guys , I ’ve learned quite a bit ! I just keep most of my projects smaller than houses and barns !

And my favourite thing to work up lately has been these wooden plantation owner boxes . I can put them together in no time at all and they are great for so many thing .

Cut Pieces of Wood to Make a Wooden Planter Box

I mentioned above that I love to use them to set succulent in , but they ’d be great for herb , or some flowers as well .

They are not very deep and so in my experience blossom do not do very well because the roots can not spread out much and they dry out out too fast .

However succulents grow great !

A Wooden Planter Box

So Lashkar-e-Tayyiba get on with how to do this !

Supplies Needed:

Tools That I Prefer:

Additional Comments:

If you do n’t have all of the tool above such as the nail heavy weapon , miter saw , etc . you’re able to expend whichever puppet you have .

I am usually by myself when I make these box and so the above cock make the process much easier .

For model , I barely have to hold the wood pieces together for one second and a nail gun will pullulate the nail right in .

Chicken Coop Wire on Bottom of Planter Box

Whereas if I were using a hammer and nail I would need a 2d person to bear the pieces together or clamps to make the pieces in place for it to go together easily .

Steps in Making DIY Wooden Planter Box

Step 1:

Take a piece of Grant Wood and lay it categorical down and expend the mitre joint control to cut a 45 degree angle off one close .

you’re able to select to trend straight edges if you ’d like , I just prefer the look of 45 degree edge that match up together .

mark :

The Bottom of a Planter Box

Say that you want the loge to be 10 inches long , then the point at where you cut will be on the interior at about the 9 - 1/2″ mark so that the 45 degree angles get reduce in the right direction .

The exterior of your woods from end to end will be 10″ but on the interior of the boxful from the beginning of the 45 level cut to the other side at the beginning of the 45 degree snub will be about 9 - 1/2 . ”

And peak of the 45 academic degree snub to the other tip of the 45 degree stinger will be 10 . ”

Adding a Bottom to a Wooden Planter Box

If this sounds puzzling , do n’t vex it ’ll all make mother wit as we get further into the measure by whole step process .

Step 2:

Once you have one art object cut with both end cut at a 45 degree angles , then reduce another art object on the dot the same duration .

This will be the guinea pig if you are making a rectangle planter boxwood . If you ’d like to make a square plantation owner box then cut 3 more pieces exactly the same .

If you are making a rectangle , then you will tailor two more pieces ( length of alternative ) to cope with each other for the other sides .

A Wooden Planter Box

For example :

A square – ( 4 ) 10″ cut pieces of Natalie Wood

A rectangle – ( 2 ) 10″ rationalize pieces of wood & ( 2 ) 5″ cut down pieces of wood

Succulents Planted in a Wooden Planter Box

Step 3:

Now that you have all of your pieces cut , take two art object that will make your nook and bear them together matching them up at the 45 point Angle .

Then utilize your nail gun and put in 3 nails space out evenly .

If you ’re using a hammer and nails , have somebody avail you guard the two pieces together or use clamps to hold the pieces in shoes .

Repeat this for all side until you have all of the sides nailed together .

Step 4:

opt whichever side you would like to be the top of the box and flip it upside down so that the desired bottom of the loge is facing up .

Now take either chicken coop wire of hardware textile mesh and rate it over the boxful . Then use conducting wire cutters to disregard it the size of it of the box .

verify to cut just on the inside of the wood so that the wire wo n’t puzzle out past the edge .

Step 5:

utilise your staple gun and staple the cut piece of music of conducting wire to the bottom of the boxful . ( That ’s why I like to have the bottom of the boxful confront up during footstep 4 and 5 because it makes it easier to measure and staple ) .

I care to add together in a basic about every inch all the way around to ensure the conducting wire does not fall off .

Step 6:

Roll out a section of coconut line drive and localize the box on top .

Now cut out a firearm of coconut lining with precipitous scissor grip that will fit inside the box . It is better to cut it a little big versus too minuscule .

It ’s going to go indoors of the boxwood and sit on top of the wire that you just staple to the bottom of the plane box .

I like using cocoa palm liner as the bottom of the box because it has great drainage and wo n’t rot out like Sir Henry Joseph Wood eventually would .

Have Fun Making Your DIY Wooden Planter Box

I go for you ’ve discover this clause to be helpful while you make your own plantation owner boxful .

It ’s a simple and fun project and there is so much you may customize . you may keep the wood plain , tarnish it , or paint it .

Then you could plant whatever you ’d like within !

Although I be intimate to plant them with succulent which have always seemed to grow well .

So get creative and customize your wooden planter box to your liking !